Kanyakumari - Beauty of Kanyakumari at SunSet & Moon Rise..

FOR MORE DETAILS ABOUT KANYAKUMARI TOURIST PLACES and TOUR EXPERIENCE
VISIT THE BEAUTIFUL full fledged Kanyakumari website which is shown below:- Clicking that link take you to that Beautiful page :-
                                                http://heartin-kanyakumari.blogspot.in

   
In the Above website you get the details of 
1.) Train , Bus , Flight timings to reach kanyakumari
2.) Beautiful photos with details of all tourist places.
3.) Route map of all tourist places in there
4.) Personal Journey Experience Review of all tourist places.
5.) Videos of that particular tour place.





  Kanyakumari is famous for its spectacular sunrises and sunsets, especially on full moon days. It is at its best during Chitra Pournami (full moon day in April) when the sun and moon are face to face at the same horizon. but other full moon days are also special when you can see the sun set and the moon rise almost simultaneously, as if by prior arrangement.The beach itself is a beautiful sight with multi-coloured sand. Palmleaf articles of Kanniyakumari are very much world famous.

Chitra Poornima is the name of Full Moon on Tamil month of Chitra.This occurs when our Sun is in its Exalted state of Aries (close to the Earth), and Moon is full and aligned with the bright star called Chitra in the constellation of Libra

Kanyakumari Distance Chart

Chennai – 703KM | Bangalore – 674KM | Cochin – 304KM | Kottayam – 267KM | Coimbatore – 469KM
Kodaikanal – 349KM | Thekkady – 294KM | Madurai – 624KM | Rameswaram – 295KM | 

Thanjavur – 400KM Trichy – 384KM | Trivandrum – 87KM | Velankanni – 489KM

Kanyakumari –Little known Facts

• ·   Main Kanyakumari temple is dedicated to Devi Kumari (Kumari Amman Temple) and it is over 3000 years old.
• ·  During peak season, the ferry service to Vivekananda rock memorial is used by over 10,000 tourists per day!
• ·  Sunrise is visible throughout the year in Kanyakumari, but sunset is visible only from October 15 to March 15.
• ·  From the hillock called Murugan Kundram (3KM from Kanyakumari), both sunset and sunrise is visible throughout the year.
• ·   Full moon day of April is the best day to visit Kanyakumari (Chithra Pournami).
• ·   Swami Vivekanandan attained enlightenment while meditating on the Kanyakumari rock in 1892.
• ·   Vivekananda memorial was constructed in 1970 and it took 650 men and 2000+ days to complete construction.
• ·  Mahatma Gandhi visited Kanyakumari in 1925 and 1937. There is a Gandhi memorial on the beach side.
•  

 

 

                                                     EARLY MORNING SUNRISE from the SEA LEVEL

                                                      SUNRISE little bit above.....

                               SUNRISE little bit above.....and given Sexy orange eye catching view .... 

                                 SUNRISE little bit above.....and then Clouds trying to hide SUN .... 

                                                   SUN with Full bright ...eye catching view .... 

                                                 No SUN and Rainy effect in mid-day .... 

                                                SUNSET at evening ... eye catching view .... 

                                     SUN become dim and beautiful rays spread on .... 

                        Last moments of SUNSET ....within few minutes it will go and MOON rise soon.. 

             MOON RISE little bit above.....and given Mind touching peaceful golden eye catching view .... 

                                          MOON above the 133 Feet tall statue....at 9pm 

   MOON from long shot and in background of vivekananda rock & thiruvalluvar statue at night 12pm .... 

                         MOON SET at early morning, eye catching view .... at 3am

                             MOON SET at early morning, eye catching view .... at 5am

                    Early morning, eye catching view .... with Rainy Clouds and calm waves...

We cant explain our personal feelings and beautiful moments only through Photo's ..its possible u come and feel it in your own way and touch... don't miss the chance in your life, at least once come to this place and enjoy the pleasure..its up to u...

FOR MORE DETAILS ABOUT KANYAKUMARI TOURIST PLACES and TOUR EXPERIENCE
VISIT THE BEAUTIFUL full fledged Kanyakumari website which is shown below:- Clicking that link take you to that Beautiful page :-
                                                http://heartin-kanyakumari.blogspot.in

Tool Design - BASICs of PLASTIC MOLD..Part-2

Classification or types of mold injection very depend on what we need to make the plastic parts, because every parts have specific and unique design. when design molds we must see what the influencing factor like geometry, number of cavities, ejection principle, plastic material and shape of parts.

The basic classification of mold based on construction shown on picture below


1. Standard Molds
the standard mold is the most simple design, basically the standard molds is same as two plate molds construction, they divided in two side : cavity side and core side, cavity side is the side that construct to flowing plastic material from nozzle to cavity parts, basically they consist of sprue, runner.

core side construct to make shape for core, demolding system and ejection system, at this side we design ejection system.
standard mold have one parting line, and have one opening direction. this type of mold use in all kinds of plastic parts that doesn't have undercut, inner and outer screw.
Light brown color little and straight in ejection system is shown ejector pin.




2. Slide mold or Split mould
development from this mold type is the used slider parts in various molds types, basic slide mold is transfer horizontal movement of mold to vertical movement, this types of molds is used to make parts with undercut, you should see more at the post when we need slider for learn more.

3. Three plate molds
basically three plate molds has two parting line, and floating plate, floating plate support by support pin, Since the mold has two parting planes, the runner system can be located on one side of floating plate or make special plate that attach in floating plate, we called runner plate, see post about runner plate. Three plate molds are used because of their flexibility in gating location. this types of molds is flexible even use in multiple cavity.

note : floating plate also called cavity plate or plate number 3, to know more the different between two plate mold and three plate mold see the posting about Basic and Types Molds Construction

4. Split Cavity Mold
basically the split cavity is same as 2 plate standard mold, but the cavity have split block to make undercut product or external threads.


this type of mold use when the slider is not enough to make the undercut or the threads. the disadvantages of this mold is when use for little parts, the construction will difficult.

5. Mold With Screw Device
this mold special to make thread forming, the core can be rotate when demolding process, both internal or external threads can be forming by this type mold.





from those picture we can see that they have gear device, the gear will rotate when form thread.

6. Stripper Ejector Mold
this type of mold have special purpose to make a cup shape without undercut, stripper ejector will make ejection more easy, same movement and power at the product and without a lot of marks in product






Molds with complex and difficult design can be integrated or combined one to the others mold type.

Tool Design - BASICs of PLASTIC MOLD..Part-I

A mold plate is any plate required to built a complete mold, in all plate use for molds have the main requirements, they are :
1. Good corrosion resistant
2. Good Machinability.
3. Easy to clean
3. Good heat transfer.
4. Homogeneity of steel.
5. Easy ability.
6. Low Cost.

at picture below you can see 3 plate mold base type with closed position, basically 3 plate type and 2 plate type has some main plate, see explanation about mold construction type to understand more, in next post or PART-2


explanation below based on number at those picture
1. Fixed Clamping Plate or Top Plate
Holds The fixed side of the mold to attached at the fixed platen of the injection machine. at this plate will attach locating ring, eye bolt, and sprue bush.
2. Runner Stripper Plate
this plate only used in 3 plate molds type, the function is to cut resin from nozzle in top of sprue bush, and pull the runner by runner locking pin.
3. Fixed Mold Plate or Cavity plate.
use to hold cavity side of product, leader pin, support pin, Puller bolts, and Angular pin when slider attached.
4. Movable Cavity Plate or Cavity plate
it used to attach core side of product, return pin, leader bush and slider core if needed.
5. Back up Plate or Support plate
used to support cavity plate, attach the hole for return pin's spring, and cooling channel when in cavity plate can not make it.
6. Spacer Block
Mounted between the movable clamping plate (bottom plate) and the movable cavity plate to give space and allow the ejector plate to move when ejecting the
part. the required length of spacer block depend on ejector stroke that needed to eject product.
7.Ejector retainer plate
to hold the ejector, Z pin, shoulder bolts,and give space to ejector leader pin and support pillar.
8. Ejector Plate
Pushes the ejector pins and return pins, connected with ejector rods.
9. Movable Clamping Plate or Bottom plate
Holds The movable side of the mold like spacer block, support plate, cavity plate and ejector mechanism to the movable platen of the injection machine.


and look at picture below, shown 3 plate molds type in opening position, but at picture below, Bottom plate or movable clamping plate is number 7, number 8 is ejector retainer plate, and number 9 is ejector plate.